• SEARCH
  • LANGUAGE - English

LAND ROVER ACCESSORY FITTING INSTRUCTIONS

VEHICLE :
PART NO :
KEYWORD :

LAND ROVER

DEFENDER

TOWING SYSTEMS - COMMERCIAL - 90 / 110

VPLET0336 - VPLET0337 / VPLET0272 / VPLET0273 / VPLET0274 / VPLET0275 - VPLET0276 / LR007225 / VPLKT0318 / LR171050 / LR171051 / LR146872 / LR081321 / LR131553 - LR131554 / LR131555 - LR131556 / LR140125 - LR135963 / LR153311 - LR156942 / LR153310 - LR156941 / VPLEY0116 - VPLEY0117 / LR140124 - LR135961 / VPLEY0115 - VPLEY0118 / LR171044 / LR171046 / VPLET0339 / VPLET0519 / FN106046

FITTING INSTRUCTION

WARNING
  • Accessories which are not correctly installed can be dangerous.
  • Before ordering and installing the accessory, you must read all the instructions. The correct accessory / part must be ordered for your variant of the vehicle.
  • You must follow all instructions. If in doubt, contact your nearest approved retailer.
Accessories Part Number
Electrically Deployable Towbar (Coil Suspension) VPLET0337
Electrically Deployable Towbar (Air Suspension) VPLET0336
Detachable Towbar VPLET0272
NAS Towbar VPLET0273
Australian Towbar VPLET0274
Multi-height Drop Plate Towbar (Coil Suspension) VPLET0275
Multi-height Drop Plate Towbar (Air Suspension) VPLET0276

Electrically Deployable Towbar (Bill of Materials)

WARNING
  • See Owner's handbook for model specific trailer mass and nose load limits.
CAUTION
  • Under no circumstances is the motor to be removed from the towbar armature when being replaced. The complete armature assembly needs to be returned otherwise any claim will be rejected.
NOTE
  • Towing eye cover (A) needs ordering in your correct bumper color and may require painting before installation. See table below for details.
  • For motor vehicle data see sheet at the end of these instructions.
Bill of Materials Part Number
(A) Towing Eye Cover - Ceres Silver / Silicon Silver / Narvik Black (Comes primed and requires painting) LR135963
(A) Towing Eye Cover - Shadow Atlas (Does not require painting) LR153311
(A) Towing Eye Cover - Starlight Satin Chrome (Does not require painting) LR140125
(A) Towing Eye Cover - Nobel Chrome (Does not require painting) LR156942
(B) Electrically Deployable Towbar VPLET0336 (Air) / VPLET0337 (Coil)
(C) Towbar Fixing - x2 VPLET0336 (Air) / VPLET0337 (Coil)
(D) Module Holder VPLET0339
(E) Towbar Control Module (TBM) VPLKT0318
(F) Nut FN106046
(G) Electrically Deployable Towbar Harness - Defender 90 LR171050
(G) Electrically Deployable Towbar Harness - Defender 110 (Does not matter what part number you order) LR171051 / LR174546
(H) Switch LR081321
(J) Single Switch Bezel LR131553 (Lunar) / LR131554 (Ebony)
(J) Double Switch Bezel LR131555 (Lunar) / LR131556 (Ebony)
(K) Tie Straps - x8 LR007225
(L) Plug-in Hybrid Electric Vehicle (PHEV) Clip LR146872

Detachable Towbar (Bill of Materials)

WARNING
  • See Owner's handbook for model specific trailer mass and nose load limits.
NOTE
  • Towing eye cover (A) needs ordering in your correct bumper color and may require painting before installation. See table below for details.
  • For motor vehicle data see sheet at the end of these instructions.
Bill of Materials Part Number
(A) Towing Eye Cover - Ceres Silver / Silicon Silver / Narvik Black (Comes primed and requires painting) LR135963
(A) Towing Eye Cover - Shadow Atlas (Does not require painting) LR153311
(A) Towing Eye Cover - Starlight Satin Chrome (Does not require painting) LR140125
(A) Towing Eye Cover - Nobel Chrome (Does not require painting) LR156942
(B) Detachable Towbar VPLET0272
(C) Towbar Fixing - x2 VPLET0272
(D) Module Holder VPLET0339
(E) Trailer Module (TRM) VPLYT0295
(F) Nut FN106046
(G) Detachable Towbar Harness - Defender 90 LR171044
(G) Detachable Towbar Harness - Defender 110 (Does not matter what part number you order) LR171046 / LR177600
Detachable Towing Swan Neck (Air Suspension) LR130315
Detachable Towing Swan Neck (Coil Suspension) LR130317

NAS Towbar (Bill of Materials)

WARNING
  • See Owner's handbook for model specific trailer mass and nose load limits.
NOTE
  • Towing eye cover (A) needs ordering in your correct bumper color and may require painting before installation. See table below for details.
  • For motor vehicle data see sheet at the end of these instructions.
Bill of Materials Part Number
(A) Towing Eye Cover - Ceres Silver / Silicon Silver / Narvik Black (Comes primed and requires painting) LR135961
(A) Towing Eye Cover - Shadow Atlas (Does not require painting) LR153310
(A) Towing Eye Cover - Starlight Satin Chrome (Does not require painting) LR140124
(A) Towing Eye Cover - Nobel Chrome (Does not require painting) LR156941
(B) NAS Towbar VPLET0273
(C) Towbar Fixing - x2 VPLET0273
(D) Module Holder VPLET0339
(E) TRM VPLYT0295
(F) Nut FN106046
(G) NAS Towbar Harness - Defender 90 LR171044
(G) NAS Towbar Harness - Defender 110 (Does not matter what part number you order) LR171046 / LR177600
NAS Towbar Hitch (Air Suspension) VPLEY0116
NAS Towbar Hitch (Coil Suspension) VPLEY0117

Australian Towbar (Bill of Materials)

WARNING
  • See Owner's handbook for model specific trailer mass and nose load limits.
NOTE
  • Towing eye cover (A) needs ordering in your correct bumper color and may require painting before installation. See table below for details.
  • For motor vehicle data see sheet at the end of these instructions.
Bill of Materials Part Number
(A) Towing Eye Cover - Ceres Silver / Silicon Silver / Narvik Black (Comes primed and requires painting) LR135961
(A) Towing Eye Cover - Shadow Atlas (Does not require painting) LR153310
(A) Towing Eye Cover - Starlight Satin Chrome (Does not require painting) LR140124
(A) Towing Eye Cover - Nobel Chrome (Does not require painting) LR156941
(B) Australian Towbar Deployable Towbar VPLET0274
(C) Towbar Fixing - x2 VPLET0274
(D) Module Holder VPLET0339
(E) TRM VPLYT0295
(F) Nut FN106046
(G) Australian Towbar Harness - Defender 90 LR171044
(G) Australian Towbar Harness - Defender 110 (Does not matter what part number you order) LR171046 / LR177600
Australian Towbar Hitch (Air Suspension) VPLEY0115
Australian Towbar Hitch (Coil Suspension) VPLEY0118

Multiheight Drop Plate Towbar (Bill of Materials)

WARNING
  • See Owner's handbook for model specific trailer mass and nose load limits.
NOTE
  • Towing eye cover (A) needs ordering in your correct bumper color and may require painting before installation. See table below for details.
  • For motor vehicle data see sheet at the end of these instructions.
Bill of Materials Part Number
(A) Towing Eye Cover - Ceres Silver / Silicon Silver / Narvik Black (Comes primed and requires painting) LR135961
(A) Towing Eye Cover - Shadow Atlas (Does not require painting) LR153310
(A) Towing Eye Cover - Starlight Satin Chrome (Does not require painting) LR140124
(A) Towing Eye Cover - Nobel Chrome (Does not require painting) LR156941
(B) Multiheight Drop Plate Towbar VPLET0274
(C) Towbar Fixing - x2 VPLET0274
(D) Module Holder VPLET0339
(E) TRM VPLYT0295
(F) Nut FN106046
(G) Multiheight Towbar Harness - Defender 90 LR171044
(G) Multiheight Towbar Harness - Defender 110 (Does not matter what part number you order) LR171046 / LR177600
(H) Drop Plate VPLET0274
(J) M16 Screw - x4 VPLET0274
(K) M16 Nut - x6 VPLET0274
(L) Tow Ball VPLET0274
(M) M16 Bolt - x2 VPLET0274
(N) Plate VPLET0274
(P) M6 Bolt - x2 VPLET0274
(R) M6 Nut - x2 VPLET0274
(S) Spacer - x2 VPLET0274

Additional part required 'ONLY' if the 'Deployable Side Steps' are already installed to your vehicle.

Bill of Materials Part Number
(I) Deployable Side Step Bracket VPLEP0519

Warnings / Cautions / Notes

CAUTION
  • When vehicle is being rased on ramp, there is a risk of damage to vehicle if the exhaust or Diesel Exhaust Fluid (DEF) tank are not supported correctly when partly removed for access.
NOTE
  • The following steps apply to all Defender 90 and 110 model variants unless stated. Some illustrations will look different depending on vehicle variant, but the essential information is correct.
  • Paid subscription to TOPIX required to view workshop manual links.
Fitting Instruction
1

Disconnect the 12V battery.

  • Log into TOPIX and enter your 17 character 'Vehicle Identification Number' and navigate to 'Workshop Manual' section '414-00 12V System Disconnect and Connect'.
2
NOTE
  • Defender 110 shown. Defender 90 is similar.

Remove loadspace rear trim panel.

3
NOTE
  • Defender 110 shown. Defender 90 is similar.

Remove x14 fixings to remove the cargo barrier stowage compartment.

4
NOTE
  • This step is 'ONLY' applicable for Defender 90.

Remove rubber mat.

5
NOTE
  • This step is 'ONLY' applicable for Defender 90.

Remove rear left D-loop and remove x7 fixings to remove panel.

6
NOTE
  • This step is 'ONLY' applicable for Defender 110.

Remove x2 D-loops and x2 fixings and remove the lower cover.

7

Remove x2 fixings and pull loadspace treadplate away from its x4 clips underneath to remove the treadplate.

8

If you are not installing the 'Electrically Deployable Towbar' then continue from step 18.

9
NOTE
  • This step is 'ONLY' applicable for the 'Electrically Deployable Towbar' with a switchpack already present. If a switchpack is not present then continue to next step.
  • Defender 110 shown. Defender 90 is similar.

Release 'Left Loadspace Trim Panel' to gain access behind. Then continue from step 18.

  1. Remove tailgate latch cover then remove x2 fixings underneath cover.
  2. Remove x2 fixings to remove the tailgate sticker.
  3. Deploy the coat hanger to reveal fixing. Then remove fixing.
10
NOTE
  • This step is 'ONLY' applicable for the 'Electrically Deployable Towbar' that has no switches already present in the 'Left Loadspace Trim Panel' .

If there is no switchpack located in the area shown on the graphic. Then the 'Left Loadspace Trim Panel' must be removed for cutting. See table below for your variant of vehicle.

Variant of Vehicle Steps
Defender 90 Steps 11-13 / 17
Defender 110 Steps 14-16 / 17
11
NOTE
  • This step is 'ONLY' applicable for Defender 90 installation for the 'Electrically Deployable Towbar' that has no switch panel present in step 10.

Remove x6 fixings to remove rear left cargo barrier side panel.

12
NOTE
  • This step is 'ONLY' applicable for Defender 90 installation for the 'Electrically Deployable Towbar' that has no switch panel present in step 10.

Remove x8 fixings to remove front left cargo barrier side panel.

13
NOTE
  • This step is 'ONLY' applicable for Defender 90 installation for the 'Electrically Deployable Towbar' that has no switch panel present in step 10.

Remove left loadspace trim panel.

  • Log into TOPIX and enter your 17 character 'Vehicle Identification Number' and navigate to 'Workshop Manual' section '501-05 Interior Trim and Ornamentation'.
14
NOTE
  • This step is 'ONLY' applicable for Defender 110 installation for the 'Electrically Deployable Towbar' that has no switch panel present in step 10.

Remove cargo barrier stowage compartment.

  • Log into TOPIX and enter your 17 character 'Vehicle Identification Number' and navigate to 'Workshop Manual' section '501-05 Interior Trim and Ornamentation'.
15
NOTE
  • This step is 'ONLY' applicable for Defender 110 installation for the 'Electrically Deployable Towbar' that has no switch panel present in step 10.

Remove left C-Pillar upper trim panel.

  • Log into TOPIX and enter your 17 character 'Vehicle Identification Number' and navigate to 'Workshop Manual' section '501-05 Interior Trim and Ornamentation'.
16
NOTE
  • This step is 'ONLY' applicable for Defender 110 installation for the 'Electrically Deployable Towbar' that has no switch panel present in step 10.

Remove the tailgate striker (arrowed white) and the tailgate latch guide trim (arrowed black) then remove the left loadspace trim panel.

  • Log into TOPIX and enter your 17 character 'Vehicle Identification Number' and navigate to 'Workshop Manual' section '501-05 Interior Trim and Ornamentation'.
17
WARNING
  • Make sure to wear suitable personal protective equipment.
NOTE
  • This step is 'ONLY' applicable for 'Electrically Deployable Towbar' that has no switch panel present in step 10.

Remove the loadspace trim panel and cut a hole in the loadspace trim for the electrically deployable towbar switch (H).

  1. Identify the correct cut guide lines on the reverse of the loadspace trim panel.
  2. Use suitable tooling to cut the identified sections from the loadspace trim panel. Discard the removed sections.
18
NOTE
  • This step applies 'ONLY' if your vehicle is a Mild Hybrid Electric Vehicle (MHEV) .

Remove the section of air ducting as illustrated to allow access for when you install the towing harness.

19
NOTE
  • This step 'ONLY' applies to vehicles installed with rear antenna module.

Remove x2 fixings to move aside antenna module to gain access to the back panel studs behind.

20

Raise vehicle on ramp.

21
NOTE
  • This step requires the aid of another technician.

Remove the rear bumper.

  • Log into TOPIX and enter your 17 character 'Vehicle Identification Number' and navigate to 'Workshop Manual' section '501-19 Bumpers'.
22

Remove and retain x3 trim fixings to remove the rear bumper lower cover from the rear bumper.

23

Lower vehicle on ramp to gain access to the loadspace.

24

Deployable Side Steps

  1. If your vehicle already comes equipped with 'Deployable Side Steps' proceed to steps 25 to 30 then jump to and proceed from step 33.
  2. If your vehicle does 'NOT' have 'Deployable Side Steps' then jump to and proceed to step 31.
25

Disconnect (where arrowed) and discard deployable side step link lead.

26

Disconnect deployable side step harness from Running Board Control Module (RBM) .

27

Remove x2 fixing and remove the RBM.

28
NOTE
  • Electrically Deployable module shown. NON - electrically deployable module differ in appearance but the essential information is always correct.

Slide TBM (E) into deployable side step bracket (I). Make sure the holes are aligned as illustrated.

29
NOTE
  • Electrically Deployable module shown. NON - electrically deployable module differ in appearance but the essential information is always correct.

Install TBM(E) with deployable side step bracket (I) to the bracket studs and install with the x2 fixings removed in step 27.

  • Torque: 5Nm
30

Install RBM on top of the TBM to the deployable side step bracket (I) studs with x2 fixings (F).

  • Torque: 5Nm
31

Install module bracket (D) to vehicle floor studs with x2 fixings (F).

  • Torque: 10Nm
32
NOTE
  • Electrically Deployable module shown. NON - Electrically Deployable module differ in appearance but the essential information is always correct.

Install TBM(E) to the bracket studs and install with the x2 fixings (F).

  • Torque: 5Nm
33

Remove top stud fixing.

34

Remove rubber grommet and cable tie clip.

35
NOTE
  • Electrically Deployable Towbar harness shown. NON - electrically deployable towbar harness is similar but does not have connections (GK, GJ and GI).

Familiarize yourself with the harness.

  • Connector (GE) is only used to connect to the RBM when deployable side steps are present. If your vehicle does not have deployable side steps then tape this connecter to the main harness to keep it out of the way.
36
NOTE
  • Electrically Deployable Towbar harness shown. NON - Electrically Deployable Towbar harness differ in appearance but the essential information is always correct.

Feed the electrical harness (G) through the back panel as illustrated and fasten harness where arrowed.

  1. Connect connector (GC) to the main body harness.
  2. Connect ground connection (GD) to the top stud, using the fixing removed in step 33.
  3. Torque: 10Nm
37
NOTE
  • This step 'ONLY' applies to vehicles installed with rear antenna module.

Install the antenna module back to its original position with x2 fixings.

  • Torque: 10Nm
38
NOTE
  • This step applies 'ONLY' to the installation of the 'Electrically Deployable Towbar' module.
  • If deployable side steps RBM is installed the TBM will be located under the RBM.

Connect connectors (GA), (GJ) and (GB) to the TBM(E).

39
NOTE
  • This step applies 'ONLY' to the installation of the NAS / Austrailian / Detachable or Multi-height towbar modules.
  • If deployable side steps RBM is installed the TRM will be located under the RBM.

Connect connectors (GA) and (GB) to the TRM(E).

40
NOTE
  • This step applies 'ONLY' if you have 'Deployable Side Steps' installed.

Reconnecting the RBM.

  1. Connect the deployable side step harness back to the RBM (where arrowed), and then fasten with cable tie (K).
  2. Connect towbar harness connector (GE) to RBM.
41
NOTE
  • This step applies 'ONLY' if your vehicle is a MHEV.

Install the section of air ducting as illustrated if it was removed earlier.

42
CAUTION
  • Avoid trapping the harness and route the harness away from any sharp objects.
NOTE
  • Complete step applies 'ONLY' to Electrically Deployable Towbar to NON-PHEV or NON-MHEV vehicles.

Move the loadspace side trim aside to allow access. Route the electrical harness (G) as illustrated, and fasten the electrical harness to the vehicle body with the clip (arrowed) and x2 cable ties (K). Then jump to and proceed from step 45.

43
CAUTION
  • Avoid trapping the harness and route the harness away from any sharp objects.
NOTE
  • Complete step applies 'ONLY' to Electrically Deployable Towbar to Defender 110 MHEV vehicles.

Move the loadspace side trim aside to allow access. Route the electrical harness (G) as illustrated, and fasten the electrical harness to the vehicle body with the clip (arrowed) and x3 cable ties (K). Then jump to and proceed from step 45.

44
CAUTION
  • Avoid trapping the harness and route the harness away from any sharp objects.
NOTE
  • Complete step applies 'ONLY' to Electrically Deployable Towbar to PHEV vehicles.

Move the loadspace side trim aside to allow access. Route the electrical harness (G) as illustrated, and fasten the electrical harness to the vehicle body with the clip (arrowed) and x3 clips (L).

45
NOTE
  • This step applies 'ONLY' to Electrically Deployable Towbar.

Connect the switch (H) to the connector (CK).

46

Raise vehicle on ramp.

47
WARNING
  • Care must be taken when working near the exhaust system as it can be very hot. Failure to follow this instruction may result in personal injury.
CAUTION
  • The exhaust system must be supported. Failure to follow this instruction may damage the component.
  • When vehicle is being rased on ramp, there is a risk of damage to vehicle if the exhaust or DEF tank are not supported correctly when partly removed for access.

Remove the rear exhaust.

  • Log into TOPIX and enter your 17 character 'Vehicle Identification Number' and navigate to 'Workshop Manual' section '309 Exhaust System'.
48
NOTE
  • For diesel vehicles 'ONLY' equipped with DEF Tank.

If relevant to your vehicle drain and remove the DEF tank

  • Log into TOPIX and enter your 17 character 'Vehicle Identification Number' and navigate to 'Workshop Manual' section '303 Engine Emission Control'.
49
NOTE
  • This step contains some variation in the illustration depending on the vehicle specification, but the essential information is always correct.

Remove x4 or x6 fixings and remove exhaust heatshield depending on your vehicle specification to gain access to the rear bumper armature fixings.

50

Remove and retain the recovery plates (S1), (S2) and x8 fixings (S3).

51

Remove and retain x6 fixings (S4). There are x3 fixings on each side of the bumper armature.

52
WARNING
  • This step requires the aid of another technician (heavy component).

Remove and retain x8 fixings (S5) and remove the rear bumper armature.

53
WARNING
  • This step requires the aid of another technician (heavy component).
CAUTION
  • Take care to avoid damaging or obscuring the towing harness connectors as the towbar is installed.

Offer up the towbar (B) to the vehicle.

  • Install, but do not fully tighten x8 fixings (S5).
54
NOTE
  • Install, but do not fully tighten the bolts.

Complete on both sides of the vehicle, install x2 fixings (C) and x6 fixings (S4).

55

Tighten fixings.

  • (S5) Torque: 115Nm + 120º
  • (S4) Torque: 140Nm + 300º
  • (C) Torque: 115Nm + 120º
56

Install the recovery plates (S1) and (S2) to the towbar using x8 fixings (S3).

  • Torque: 170Nm
57
NOTE
  • This step applies 'ONLY' to Electrically Deployable Towbar - (VPLET0336 / VPLET0337).

Connect connector (GI) to the 'Electrically Deployable Towbar' motor and fasten the harness to the armature with the clip (arrowed).

58

Connect the connectors (GF) and (GH) to the towbar.

59
NOTE
  • This step contains some variation in the illustration depending on the vehicle specification, but the essential information is always correct.

Install x4 or x6 fixings and install the exhaust heatshield depending on your vehicle specification.

60
NOTE
  • For diesel vehicles 'ONLY' equipped with 'Diesel Exhaust Fluid Tank'
  • Perform pull/push test to make sure robust connection has been made and that there are no leaks.
  • Make sure all diesel exhaust fluid tank harness connectors are correctly installed and audible click heard on installation. Perform pull/push test to make sure robust connection has been made. make sure all harness clips are reinstalled in their original locations on the diesel fluid tank and the vehicle body.
  • Make sure the diesel exhaust fluid injector pipe clips to the body are correctly installed. Make sure that the pipe is not damaged and does not have any leaks from connections.
  • Fill the diesel exhaust fluid tank with any fluid that was removed during removal.

Install the diesel exhaust fluid tank if applicable to your vehicle.

  • Log into TOPIX and enter your 17 character 'Vehicle Identification Number' and navigate to 'Workshop Manual' section '303 Engine Emission Control'.
61
NOTE
  • This step contains some variation in the illustration depending on the vehicle specification, but the essential information is always correct.

Install rear exhaust.

  • Log into TOPIX and enter your 17 character 'Vehicle Identification Number' and navigate to 'Workshop Manual' section '309 Exhaust System'.
62
NOTE
  • Before installation of towing eye cover (A) see 'Bill of Materials' to see if your towing eye requires painting.

Install the towing eye cover (A) to the bumper with the x3 retained trim screws.

63
NOTE
  • This step requires the aid of another technician.

Install the rear bumper.

  • Log into TOPIX and enter your 17 character 'Vehicle Identification Number' and navigate to 'Workshop Manual' section '501-19 Bumpers'.
64

Lower vehicle on ramp.

65
NOTE
  • This step applies 'ONLY' to the installation of the electrically deployable towbar.

Offer up the 'Left Loadspace Trim Panel' back to the original position. Then install the switch panel (J) to the electrically deployable towbar switch (H), then install the switch panel (J) to the loadspace left trim panel.

  • After the switch is installed, then install the 'Left Loadspace Trim Panel' back the vehicle. Log into TOPIX and enter your 17 character 'Vehicle Identification Number' and navigate to 'Workshop Manual' section '501-05 Interior Trim and Ornamentation'.
66

Clip loadspace treadplate back into position and install x2 fixings.

  • Torque: 4.1Nm
67
NOTE
  • This step is 'ONLY' applicable for Defender 110.

If removed install the left C-Pillar upper trim panel.

  • Log into TOPIX and enter your 17 character 'Vehicle Identification Number' and navigate to 'Workshop Manual' section '501-05 Interior Trim and Ornamentation'.
68
NOTE
  • This step is 'ONLY' applicable for Defender 110.

If removed install cargo barrier stowage compartment.

  • Log into TOPIX and enter your 17 character 'Vehicle Identification Number' and navigate to 'Workshop Manual' section '501-05 Interior Trim and Ornamentation'.
69
NOTE
  • This step is 'ONLY' applicable for Defender 90.

If removed install x8 fixings to the front left cargo barrier side panel.

  • Torque: 6Nm
70
NOTE
  • This step is 'ONLY' applicable for Defender 90.

If removed install x6 fixings to the rear left cargo barrier side panel.

  • Torque: 6Nm
71
NOTE
  • This step is 'ONLY' applicable for Defender 110.

Install left lower cover.

  • x2 D-Loops - Torque: 24Nm
  • x2 Fixings - Torque: 3.5Nm
72
NOTE
  • This step is 'ONLY' applicable for Defender 90.

Install left lower panel.

  • D-Loops - Torque: 24Nm
  • x7 Fixings - Torque: 3.5Nm
73
NOTE
  • This step is 'ONLY' applicable for Defender 90.

Install rubber mat.

74
NOTE
  • Defender 110 shown. Defender 90 is similar.

Install x14 fixings to the cargo barrier stowage compartment.

75
NOTE
  • Defender 110 shown. Defender 90 is similar.

Install loadspace rear trim panel.

76

Connect the 12V battery.

  • Log into TOPIX and enter your 17 character 'Vehicle Identification Number' and navigate to 'Workshop Manual' section '414-00 12V System Disconnect and Connect'.
77
NOTE
  • Make sure step 1 is successfully completed before proceeding to step 2.

Use the JLR approved diagnostic equipment to navigate to 'Diagnostics' section and follow the steps below.

  1. Within Vehicle Applications – Click ‘RUN’ for ‘Add/Remove Electronically Deployable Towbar’, then select ADD.
  2. Within Module Programing – Click ‘RUN’ for ‘TBM - Software - Replace Module’.
    3. To enable the changes on the vehicle
    Ignition off
    Close all doors
    Lock the vehicle
    Wait 5 minutes
    To confirm changes
    Unlock the vehicle
    Reset Infotainment Screen (Refer to 'Touchscreen' settings in Owners handbook for detailed procedure.)
    Confirm ‘Tow bar' tile is present on the Touchscreen.
78
NOTE
  • This step applies 'ONLY' to electrically deployable towbar.

Inspect the operation of the electrically deployable towbar using the electrically deployable towbar switch in the vehicle loadspace and front console.

  • If the testing is unsuccessful repeat STEP 77.
79
NOTE
  • This step applies 'ONLY' to Detachable Towbar - (VPLET0272).

Before installing the detachable towing swan neck (LR130315 or LR130317) remove the x2 protective covers (arrowed). For the removal of the protective cap on the hitch follow these steps.

  1. Insert the key and turn clockwise to unlock the handwheel.
  2. Pull the handwheel away from the tow ball. Simultaneously turn the handwheel approximately half a turn counter-clockwise. The red lug on the handwheel must enter the green indicator scale.
  3. Then remove the protective cap and store in suitable location.
80
WARNING
  • Extreme care must be taken when maneuvering the tow ball / towbar hitch. Use two hands to safely maneuver into place and make sure that no body part is below the tow ball / towbar hitch during installation or removal. Failure to safely install the tow ball could result in serious injury or death.

For installation of tow ball / towbar hitch.

  • For installation of detachable towing swan neck see your vehicles Owner's Handbook.
  • For installation of the NAS towbar hitch to the NAS Towbar, refer to the Towbar Hitch - North American Market specific instruction (VPLEY0116 / VPLEY0117).
  • For installation of the AUS towbar hitch to the AUS Towbar, refer to the Towbar Hitch - Australian Market specific instruction (VPLEY0115 / VPLEY0118).
  • For installation of Multiheight tow ball see steps 81 to 85.
81
CAUTION
  • When installing the towball (L), always use fixings (M) and (K).
NOTE
  • Fixing plate (H) is only required if you are installing to the lowest position.

Install the towball. See steps 82-84 on correct position for upper, middle or lower positions.

82
NOTE
  • Do not use the fixing plate (H) for this position.

For using the towball in the top position. Position as shown (See step 81 'B' for installation).

  • Torque: 260Nm
83
NOTE
  • Do not use the fixing plate (H) for this position.

For using the towball in the middle position. Position as shown (See step 81 'B' for installation).

  • Torque: 260Nm
84
CAUTION
  • The torque applied to the fixings that install the drop plate (H) to the towbar must be applied to the nuts (K) and not to the internal hex on the countersunk screws (J).

For using the towball in the lowest position. Position as shown (See step 81 'A' for installation).

  • Torque: 260Nm
85
NOTE
  • Illustration is from underside of the vehicle.

Depending on vehicle variant 'A' or 'B' fasten the exhaust heatshield that is located close to the multiheight drop plate towbar brackets.

  1. Use the holes in the brackets as a guide to mark 1 or 2 points, as required, on the heatshield.
  2. Drill 1 or 2 holes in the heatshield as required. Use a 7mm drill bit.
  3. Install fixings (P), (R) and (S) as required. Torque: 10Nm
86
WARNING
  • Make sure the relevant safety warnings and cautions have been read and understood before towing a trailer.

Inspect the operation of the trailer lamps and the vehicle lamps. Both trailer and vehicle lights must be synchronized.

87

After the towball or towbar hitch has been removed it must be stored in a safe location.

  • The detachable tow ball must be removed if it is not required for immediate use. It can be stored on the loadspace tool tray in certain variants of the vehicle. If this is not the case then the detachable tow ball must be strapped to a suitable point in the vehicle.
  • The NAS or AUS towbar hitch is supplied in a hard plastic case that can be stored in the loadspace.
  • Install the protective covers back to the towbars after the towball or towbar hitch has been removed.
88
WARNING

Motor Vehicle Data Sheets.

Motor vehicle data, Deployable Towbar Specifications
Type Coil: 6354, Air: 5802
D-value Coil / Air: 16.9 kN
Vertical coupling load Coil / Air: 350kg
Coupling class Coil / Air: A50-X
Manufacturer Brink Towing Systems B.V.
Model application Defender
EC-type approval number towbar: Coil E11*55R01/08*11284*02
EC-type approval number towbar: Air E11*55R01/08*11283*03
Maximum trailer weight 3500kg
Motor vehicle data, Detachable Towbar Specifications
Type 323-162
D-value 16.6 kN
Vertical coupling load 200kg
Coupling class A50-X
Manufacturer Westfalia-Automotive GmbH
Model application Defender
EC-type approval number towbar E13*55R01/07*4605*00
Maximum trailer weight 3500kg
Motor vehicle data, NAS Towbar Specifications
Type 323-162
D-value 16.6 kN
Vertical coupling load 200kg
Coupling class A50-X
Manufacturer Westfalia-Automotive GmbH
Model application Defender
EC-type approval number towbar E13*55R01/07*4605*00
Maximum trailer weight 3500kg
Motor vehicle data, Australian Towbar Specifications
Type N/A
Vertical coupling load 350kg
Coupling class N/A
Manufacturer Westfalia-Automotive GmbH
Model application Defender
EC-type approval number towbar N/A
Maximum trailer weight 3500kg
Motor vehicle data, Multi-Height Towbar Specifications
Type 323-167
D-value 16.8 kN
Vertical coupling load 350kg
Coupling class A50-X
Manufacturer Westfalia-Automotive GmbH
Model application Defender
EC-type approval number towbar: Coil E13*55R01/07*4606*00
EC-type approval number towbar: Air E13*55R01/07*4607*00
Maximum trailer weight 3500kg
© Land Rover 2016