• SEARCH
  • LANGUAGE - English

LAND ROVER ACCESSORY FITTING INSTRUCTIONS

VEHICLE :
PART NO :
KEYWORD :

LAND ROVER

DEFENDER

LOADSPACE SEMI RIGID LINER TRAY

VPLES0569, VPLES0570

FITTING INSTRUCTION

WARNING
  • Accessories which are not correctly installed can be dangerous. Read the instructions carefully prior to installation. Comply with instructions at all times. If in doubt, contact your nearest approved retailer.
NOTE
  • This procedure contains some variation in the illustrations depending on the vehicle specification, but the essential information is always correct.
  • This procedure contains illustrations showing certain components removed to provide extra clarity.
  • VPLES0570 for vehicles with 110 wheelbase.
NOTE
  • VPLES0569 for vehicles with 90 wheelbase.
Fitting Instruction
1

Open the tailgate.

2

Remove the loadspace cover from the vehicle.

3

If access to the D-loop anchor points is not required then install the loadspace semi rigid liner tray (A) into the vehicle loadspace.

4
NOTE
  • Vehicles with third row seats.

If the vehicle is equipped with third row seat cup holders, then complete install steps 5 and 6.

5
NOTE
  • Vehicles with third row seats.

If the vehicle is equipped with third row seats then trim the 2 cutouts from the loadspace semi rigid liner tray as illustrated.

6
NOTE
  • Vehicles with third row seats.

Make sure the loadspace semi rigid liner tray is correctly installed as illustrated.

7
CAUTION
  • Take care not to close the tailgate when the bumper protector is installed.
NOTE
  • When not in use store the bumper protector inside the loadspace.

Install the rear bumper protector (B) if required.

  1. Position the rear bumper protector.
  2. Using the velcro strips, press the semi rigid liner tray to the bumper protector.
8
NOTE
  • The loadspace semi rigid liner tray can be used if either the fixed or the sliding D-loop anchor points are installed.
  • If the fixed or sliding D-loop anchor points are installed and access to the D-loop anchor points is required, then complete install steps 9 to 14.
  • If equipped, the 4 sliding D-loop anchor points will not be able to move along the loadspace rails.

If access to the D-loop anchor points is required then complete install steps 9 to 14.

9
WARNING
  • Make sure to wear suitable personal protective equipment.
NOTE
  • For vehicles with 110 wheelbase.

If access to the D-loop anchor points is required then trim the 2 cutouts from the loadspace semi rigid liner tray as illustrated.

10
NOTE
  • Complete step if the sliding D-loop anchor points are installed.
  • The sliding D-loop anchor points will not be able to move along the loadspace rails after the loadspace semi rigid liner tray has been installed.

Move the sliding D-loop anchor points to the ends of the loadspace rails.

11

Install the loadspace semi rigid liner tray (A) into the loadspace.

12

Make sure the loadspace semi rigid liner tray does not obstruct the 2 fixed or sliding D-loop anchor points.

13
CAUTION
  • Take care not to close the tailgate when the bumper protector is installed.

Install the rear bumper protector (B) if required.

14

Install the loadspace cover if required.

15
NOTE
  • The loadspace semi rigid liner tray and the loadspace partition can be installed together.
  • The loadspace semi rigid liner tray must be installed first and then the loadspace partition installed afterwards.

Complete install steps 16 to 20 if the loadspace semi rigid liner tray and the loadspace partition will both be installed.

16
NOTE
  • Complete step if the loadspace partition and the loadspace semi rigid liner tray are both being installed in a loadspace configured with sliding D-loop anchor points.

Remove the 2 sliding D-loop anchor points nearest to the second row seats.

17
WARNING
  • Make sure to wear suitable personal protective equipment.
NOTE
  • For vehicles with 110 wheelbase.

Trim the 2 cutouts from the loadspace semi rigid liner tray as illustrated.

18

Install the loadspace semi rigid liner tray (A) into the loadspace.

19
NOTE
  • The loadspace divider (VPLES0547) cannot be used.

Install the loadspace partition.

  1. Make sure the loadspace semi rigid liner tray does not obstruct the brackets for the loadspace partition.
20

Close the tailgate.

© Land Rover 2016