Remove D-loop anchor points.

Remove (x2) front D-loop anchor point. Repeat on other side of vehicle.

Remove (x2) loadspace rail retaining bolts. Repeat on other side of vehicle.

Adjust the second row seats to the lowest and most forward position.

Removal steps.

• Steps 2 to 19 show install of the full height, or half height, loadspace partition to vehicles with 110 wheelbase.
• If the full height, or half height, loadspace partition is already installed in vehicles with 110 wheelbase, then proceed to step 20 for installation of the loadspace divider (VPLES0547).
• If installing the full height loadspace partition to vehicles with 90 wheelbase then proceed to step 30.

If the loadspace rubber mat will be installed with the full height or half height loadspace partition then trim the cutouts from the loadspace rubber mat as illustrated.

1. Trim the 2 cutouts.
2. Trim the 2 cutouts if access to the D-loop anchor points nearest the tailgate is also required.

Install the loadspace rubber mat into the vehicle loadspace.

Install the (x2) brackets (B) using the retaining bolts (D). Repeat on other side of vehicle.

• Torque: 24 Nm

Reinstall D-loop onto the bracket (B). Repeat on other side of vehicle.

• Torque: 24 Nm

Install the (x2) brackets (C) using the retaining bolts (D). Repeat on other side of vehicle.

• Torque: 24 Nm

Install the thumbscrew (E) to the loadspace partition access door.

Install the (x2) brackets (G) to the main body of the loadspace partition, using the fixings (H).

• Torque: 15 Nm

Use a suitable trim tool to open the loadspace partition mounting slot cover on both sides of the vehicle.

1. Insert the trim tool into the cutout.
2. Open the loadspace partition mounting slot cover.

Install the loadspace partition (A) into the vehicle.

1. If the vehicle has second row seats that will slide forward, then route the loadspace partition through the rear passenger door as illustrated.
2. If the vehicle has second row seats that do not slide forward, then route the loadspace partition through the tailgate in the orientation as illustrated.

Install the loadspace partition pins to the loadspace partition mounting slots on both sides of the vehicle.

1. Carefully raise the 2 loadspace partition pins into the larger circular slots.
2. Move the loadspace partition pins over the tab that is part of the loadspace partition mounting slot bracket. Move the loadspace partition pins into the smaller circular slots.
3. Continue at step 13.

Install the loadspace partition to one side of the vehicle only. Swing the loadspace partition into the correct position and then install the loadspace partition to the other side of the vehicle.

1. Carefully raise the loadspace partition pin into the larger circular slot on one side of the vehicle.
2. Move the loadspace partition pin over the tab that is part of the loadspace partition mounting slot bracket. Move the loadspace partition pin into the smaller circular slot.
3. Swing the loadspace partition into the correct position.
4. Install the loadspace partition pin into the mounting slot on the other side of the vehicle.

Secure the base of the loadspace partition to the floor bracket (B) using the thumbscrew (F). Repeat on other side of vehicle.

• There is designed into the part a gap between the mounting bracket on the barrier and the floor mounting bracket (B) which is bolted to the vehicle.

Secure the base of the loadspace partition to the floor bracket (C) using the thumbscrew (F). Repeat on other side of vehicle.

• There is designed into the part a gap between the mounting bracket on the barrier and the floor mounting bracket (C) which is bolted to the vehicle.

Return the second row seats to the upright position.

Make sure that the loadspace partition is correctly installed.

Opening the full height loadspace partition access door.

1. Release the thumbscrew.
2. Lower the access door.

After covering the indicated distances, check that all the thumbscrews remain appropriately tightened.

• 500 km or 300 miles.
• 1000 km or 600 miles.

To remove the loadspace partition follow the steps.

1. Release the thumbscrews (F) that secure the base of the loadspace partition to the floor brackets (B) or (C).
2. Move the loadspace partition pins out of the loadspace partition mounting slots on both sides of the vehicle.
3. Protect the loadspace partition pins to make sure they do not damage the vehicle paintwork and trim.
4. Remove the loadspace partition from the vehicle through the rear door or the tailgate as appropriate.
5. Close the loadspace partition mounting slot cover on both sides of the vehicle.

Steps 21 to 29 show the install of the loadspace divider (VPLES0547).

Prepare the loadspace divider (VPLES0547). Install the center clamp bracket (H) to the loadspace divider (G) using the (x2) thumbscrews (F).

1. Make sure the loadspace divider center clamp bracket thumbscrews are not tightened.
2. Make sure the feet are screwed in.

Carefully place the loadspace divider (G) into the loadspace.

Position the loadspace divider (G) against the loadspace partition as illustrated.

Make sure the top bracket and the central clamp are positioned correctly in relation to the crossbars on the loadspace partition.

1. Position the top bracket as illustrated.
2. Install the center clamp to the loadspace partition as illustrated but do not tighten at this stage.

Use a spanner to adjust the feet so the loadspace divider is supported.

1. Extend the feet located at the base of the loadspace divider.
2. Make sure that the top bracket is correctly engaged.

Tighten the (x2) thumbscrews on the center clamp to secure the loadspace divider to the loadspace partition.

Excessive movement of the loadspace divider can be removed by adjusting the feet as required using a spanner.

After covering the indicated distances, check that all the thumbscrews remain appropriately tightened.

• 500 km or 300 miles.
• 1000 km or 600 miles.

To remove the loadspace divider follow the steps.

1. Loosen the (x2) thumbscrews on the loadspace divider center clamp.
2. Use a spanner to adjust the loadspace divider feet so the top bracket on the loadspace divider is released from the loadspace partition.
3. Release the loadspace divider center clamp and top bracket from the loadspace partition. Remove the loadspace divider from the vehicle.

Complete steps 31 to 46 to install of the loadspace partition (VPLES0544) to vehicles with 90 wheelbase.

Move front seat back and remove the forward front seat rail bolt.

Move front seat forward and remove the rear front seat rail bolt.

Remove the plastic trim from the end of the outboard seat rail. To aid removal the seat rail should be raised.

Install the bracket (C) to the outside seat rail. Complete step on both sides of the vehicle.

Install (x2) bolts removed in step 32 and 33 to secure the seat rail. Complete step on both sides of the vehicle.

• Torque: 48 Nm

Install the lower fixing plate (D) to the underside of the bracket (C) as illustrated. Repeat on other side of vehicle.

Install the upper fixing plate (E) to the bracket (C) and the lower fixing plate (D) as illustrated. Complete step on both sides of the vehicle. Repeat on other side of vehicle.

Fold down rear seats.

Use a suitable trim tool to open the loadspace partition mounting slot cover on both sides of the vehicle.

1. Insert the trim tool into the cutout.
2. Open the loadspace partition mounting slot cover.

Carefully install the upper part of the loadspace partition (A) into the vehicle through the front door.

1. Protect the loadspace partition pins to make sure they do not damage the vehicle paintwork and trim.

Install the loadspace partition pins to the loadspace partition mounting slots on both sides of the vehicle.

1. Carefully raise the (x2) loadspace partition pins into the larger circular slots.
2. Move the loadspace partition pins over the tab that is part of the loadspace partition mounting slot bracket. Move the loadspace partition pins into the smaller circular slots.

Move the loadspace partition legs (B) into the vehicle.

1. Make sure the holes in the loadspace partition legs align with the holes in the upper fixing plates (E).

Install the loadspace partition legs (B) to the upper fixing plate (E) and the lower fixing plate (D) using the thumbscrew (F). Repeat on other side of vehicle.

Install the loadspace partition legs (B) to the top part of the loadspace partition (A) using the (x2) thumbscrews (F).

• Tightening the thumbscrews (F) puts the loadspace partition under tension and closes the air gap between Part A and B. Make sure there is no air gap between Part A and B when the Fixing (F) is fully tightened.

After covering the indicated distances, check that all the thumbscrews remain appropriately tightened.

• 500 km or 300 miles.
• 1000 km or 600 miles.

To remove the loadspace partition follow the steps.

1. Release the thumbscrews (F) that secure the (x2) parts of the loadspace partition together.
2. Release the loadspace partition legs (B) from the upper fixing plate (E) and the lower fixing plate (D).
3. Remove the loadspace partition legs (B) from the vehicle through the front door.
4. Move the loadspace partition pins out of the loadspace partition mounting slots on both sides of the vehicle.
5. Protect the loadspace partition pins to make sure they do not damage the vehicle paintwork and trim.
6. Remove the upper part of the loadspace partition (A) from the vehicle through the front door.
7. Close the loadspace partition mounting slot cover on both sides of the vehicle.
8. Remove the upper fixing plate (E) and the lower fixing plate (D) from the seat rail. Complete step on both sides of the vehicle.
9. Remove the seat rail bolt and the bracket (C) from the seat rail. Complete step on both sides of the vehicle.
10. Install the plastic trim to the seat rail. Install the bolt. Torque: 48 Nm Complete step on both sides of the vehicle.