• SEARCH
  • LANGUAGE - English

LAND ROVER ACCESSORY FITTING INSTRUCTIONS

VEHICLE :
PART NO :
KEYWORD :

LAND ROVER

RANGE ROVER

TOWING ELECTRICS

LR158167 / LR158166 / VPLKT0318 / VPLYT0295 / VPLKV0132 / FN106042 / LR029806

FITTING INSTRUCTION

WARNING
  • Accessories which are not correctly installed can be dangerous. Read the instructions carefully prior to installation. Comply with the instructions at all times. If in doubt, contact your nearest approved retailer.

Towbar electrics for (7 seat) electrical deployable towbar (Bill of Materials)

Bill Of Materials Service Part Number
(A) Electrically Deployable Towing Harness LR158167
(B) Towbar Control Module (TBM) VPLKT0318
(B1) Nut - M6 FN106042
(C) Bracket VPLKV0132
(C1) Bolt - M6 LR029806

Towbar electrics for (7 seat) NAS and Australian towbars (Bill of Materials)

Bill Of Materials Service Part Number
(A) NAS / AUS Towing harness LR158166
(B) Trailer Module (TRM) VPLYT0295
(B1) Nut - M6 FN106042
(C) Bracket VPLKV0132
(C1) Bolt - M6 LR029806

Tooling

Tooling
Trim Tool
Socket Wrench
10mm Socket
Torque Screwdriver
Torque Wrench
Jaguar Land Rover Approved Diagnostic Equipment
REMOVAL INSTRUCTIONS
1

Open upper and lower tailgates.

2

Remove loadspace floor panel.

3

Remove luggage floor liner and tool kit.

4

Remove seal from inner back panel.

Fitting Instruction
1
NOTE
  • Electrical deployable harness shown. NAS and Austrilian markets do not have connectors (A3) and (A6).
  • Connectors (A6), (A8) and (A9) will be installed when you install the towbar.

Familiarize yourself with the towing harness.

2

Install harness (A)

  1. Feed harness through vehicle back panel as shown and secure back panel hole with grommet (A5).
  2. Connect ground point (A7) to back panel stud. You will first need to remove the bolt on the stud and then install ground point (A7). Then install back the fixing removed. Torque: 10Nm
  3. Clip the harness to the vehicle body were arrowed and feed under the air duct.
3

Connect towing harness connector (A4) to main vehicle body harness.

4
NOTE
  • Electrical Deployable Towbar Module (VPLKT0318) shown. For NAS and AUS towing the Trailer Light Module (VPLYT0295) is installed the same way.

Install towbar module (B) to bracket (C) with x2 fixings (B1).

  • Torque: 6Nm
5
NOTE
  • This step is only for electrical deployable towbar harness.
  • Audible click will be heard when the connectors are correctly connected.

Connect harness (A) to TBM (B) with connectors (A1), (A2) and (A3).

6
NOTE
  • This step is only for NAS and Australian towbar harness.
  • Audible click will be heard when the connectors are correctly connected.

Connect harness (A) to TRM (B) with connectors (A1) and (A2).

7
NOTE
  • Electrical Deployable Towbar Module (VPLKT0318) shown. For NAS and AUS towing the Trailer Light Module (VPLYT0295) is installed the same way.

Install TBM with bracket onto vehicle with x2 fixings (C1).

  • Torque 10Nm
8
NOTE
  • Make sure step 1 is successfully completed before proceeding to step 2.

Use the JLR approved diagnostic equipment to navigate to 'Diagnostics' section and follow the steps below.

  1. Within Vehicle Applications – Click ‘RUN’ for ‘Add/Remove Electronically Deployable Towbar’, then choose ADD.
  2. Within Module Programing – Click ‘RUN’ for ‘TBM - Software - Replace Module’.
    3. To enable the changes on the vehicle
    Ignition off
    Close all doors
    Lock the vehicle
    Wait 5 minutes
    To confirm changes
    Unlock the vehicle
    Reset Infotainment Screen (Refer to 'Touchscreen' settings in Owners handbook for detailed procedure.)
    Confirm ‘Tow bar' tile is present on the Touchscreen.
9

Install luggage floor liner and tool kit.

10

Install loadspace floor panel.

11

Close upper and lower tailgates.

12

Then proceed to install the Towbar.

  • For additional information, please refer to the official Workshop Manual. Towing Systems (Mechanical Only) (102-05)
© Land Rover 2016