• SEARCH
  • LANGUAGE - English

LAND ROVER ACCESSORY FITTING INSTRUCTIONS

VEHICLE :
PART NO :
KEYWORD :

LAND ROVER

RANGE ROVER VELAR

DEPLOYABLE SIDE STEPS

VPLYP0325, VPLYP0324, VPLYP0323, VPLYP0339, VPLYV0122, VPLYT0218, VPLYP0370

FITTING INSTRUCTION

WARNING
  • Accessories which are not properly fitted can be dangerous. Read the instructions carefully prior to fitting. Comply with instructions at all times. If in doubt, contact your nearest approved retailer.
NOTE
  • Link lead (R) may be secured to wiring harness (M).
Fitting Instruction
1

Raise and support the vehicle on a suitable 4 post lift.For additional information, please refer to the official Workshop Manual. Lifting (100-02)

2

Open the tailgate.

3

Remove the loadspace floor trim.

4
NOTE
  • This step only applies to vehicles not equipped with a spare wheel.

5
NOTE
  • This step only applies to vehicles equipped with a spare wheel.

Remove the spare wheel.

6

Remove the loadspace trim.

7

Remove the left side loadspace trim panel. For additional information, please refer to the official Workshop Manual. Loadspace Trim Panel LH/RH (501-05)

8

Disconnect the startup battery ground cable.For additional information, please refer to the official Workshop Manual. Battery Disconnect and Connect (414-01)

9

Release the Battery Junction Box (BJB).

10

Raise the vehicle.

11
NOTE
  • Left side shown. Right side is similar.

Remove and discard the air deflector.

12

Remove the engine undershield.

13

Remove the centre undershield.

14

Remove the side undershields.

15
NOTE
  • Left side shown. Right side is similar.

Following the template markings, cut the side undershield.

16
CAUTION
  • Make sure that the cover is evenly aligned against the undershield.
NOTE
  • Left side shown. Right side is similar.

Install cover (G) on to the undershield.

17
NOTE
  • Left side shown. Right side is similar.

Using a 6 mm drill, drill a total of 3 holes into the undershield as illustrated.

18
NOTE
  • Left side shown. Right side is similar.

Using rivets (J) and washers (K), secure the cover.

19
NOTE
  • Left side shown. Right side is similar.

Remove the screw.

20
CAUTION
  • Before installing the deployable side step brackets make sure the front battery cable clips are pushed up as far as possible on the location studs.

21
NOTE
  • Left side shown. Right side is similar.
  • Repeat this step for the right side using bolts (B) and bracket (E).
  • Do not torque the bolts at this step.

  1. Install bolts (B) to front bracket (C) to aid installation.
  2. Remove bolts (B).
22
NOTE
  • Left side shown. Right side is similar.
  • Repeat this step for the right side using bolts (B) and bracket (F).
  • Do not torque the bolts at this step.

  1. Install bolts (B) to front bracket (D) to aid installation.
  2. Remove bolts (B).
23
NOTE
  • Do not torque the bolts at this step.

  1. Install bolts (B) into the illustrated positions to aid installation.
  2. Remove the bolts.
24
NOTE
  • Do not torque the bolts at this step.

  1. Install bolts (B) into the illustrated positions to aid installation.
  2. Remove the bolts.
25
NOTE
  • This step is to aid installation.

 

26
CAUTION
  • Only tighten the bolts hand tight at this stage.

Secure bracket (C) using bolts (B) and the reinforcing plate (W).

  1. Install the bracket (C) to the vehicle using the reinforcing plate (W) and bolts (B).
  2. Tighten the bolts (B) hand tight.
27
CAUTION
  • Only tighten the bolts hand tight at this stage.

Secure bracket (C) using bolts (B).

28

Secure bracket (C) using bolts (B).

  • Torque: 30 Nm
29

Secure bracket (C) using bolts (B).

  • Torque: 30 Nm
30
NOTE
  • This step requires bolts (B) and bracket (E).
  • Left side shown. Right side is similar.

Repeat steps 26 to 29 for the right side of the vehicle.

31
CAUTION
  • Only tighten the bolts hand tight at this stage.

Secure bracket (D) using bolts (B) and the reinforcing plate (W).

  1. Install the bracket (D) to the vehicle using the reinforcing plate (W) and bolts (B).
  2. Tighten the bolts (B) hand tight.
32

Secure the bracket (D) using bolts (B) as illustrated.

  • Torque: 30 Nm
33

Secure the bracket (D) using bolts (B).

  • Torque: 30 Nm
34
NOTE
  • This step requires bolts (B) and bracket (F).
  • Left side shown. Right side is similar.

Repeat steps 31 to 33 for the right side of the vehicle.

35
NOTE
  • The illustrated wiring harness routing is to aid installation.

Make sure the longer section of the wiring harness (M) is installed on the right side of the vehicle as illustrated.

36
CAUTION
  • Retain the link lead.

Remove link lead (R) from wiring harness (M).

37

Remove and discard the grommet from the underside of the startup battery compartment.

38

Feed the wiring harness through to the startup battery compartment.

39
NOTE
  • This step only applies to vehicles equipped with air suspension.

  1. Route the wiring harness as illustrated.
  2. Lower the air suspension pipe retaining clip from the vehicle body.
  3. Secure the wiring harness against the vehicle body.
  4. Secure the suspension air pipe and retaining clip to the previous location as illustrated.
  5. Secure the supplied clip (S) to the air suspension pipe.
  6. Secure the wiring harness as illustrated.
40
NOTE
  • This step only applies to vehicles equipped with coil spring suspension.

Secure the wiring harness.

41

  1. Route the wiring harness as illustrated.
  2. Secure the wiring harness.
42

  1. Route the wiring harness as illustrated.
  2. Secure the wiring harness.
43

  1. Secure the wiring harness.
  2. Connect the electrical connector.
44

Install supplied cover (L) in the illustrated position.

45
WARNING
  • Before working on the fuel system make sure to study the fuel system health and safety section of this manual.
NOTE
  • This step only applies to vehicles with a fuel cooler equipped.

For additional information, please refer to the official Workshop Manual. Diesel Fuel System Health and Safety Precautions (100-00) For additional information, please refer to the official Workshop Manual. Petrol and Petrol-Ethanol Fuel Systems Health and Safety Precautions (100-00) Remove the fuel cooler.

46

  1. Route the wiring harness as illustrated.
  2. Secure the wiring harness.
47

  1. Secure the wiring harness.
  2. Connect the electrical connector.
48
NOTE
  • This step only applies to vehicles equipped with Fuel Fired Booster Heater (FFBH).

Install supplied cover (Q) to the fuel pipe in the illustrated position.

49
WARNING
  • Before working on the fuel system make sure to study the fuel system health and safety section of this manual.
NOTE
  • This step only applies to vehicles with a fuel cooler equipped.

For additional information, please refer to the official Workshop Manual. Diesel Fuel System Health and Safety Precautions (100-00) For additional information, please refer to the official Workshop Manual. Petrol and Petrol-Ethanol Fuel Systems Health and Safety Precautions (100-00) Install the fuel cooler.

50

Secure the wiring harness.

51

52

Lower the vehicle.

53
NOTE
  • If equipped.

Disconnect and release the wiring harness.

54
NOTE
  • If equipped.

Remove and discard the towbar control module.

55

Install module (N).

  1. Secure using retaining nuts (T).
  2. Torque: 10 Nm
56
NOTE
  • If equipped.

Connect and secure the wiring harness.

57

Route and secure the wiring harness (M).

58

  1. Release the main wiring harness.
  2. Secure the deployable side step wiring harness.
  3. Secure the main wiring harness.
59
NOTE
  • (R) - Link 1 Harness
  • (O) - Link 2 Harness

60

  1. Route the previously removed wiring harness link lead (R) as illustrated.
  2. Secure the wiring harness (M) to vehicle body.
  3. Using suitable tape, secure clip (U).
  4. Secure and connect the electrical connectors.
  5. Secure the link lead (R) using retaining clip (V).
61
NOTE
  • This step only applies to vehicles not equipped with a towbar.

Install the link lead (O) as illustrated.

62

Secure the BJB.

  • Torque: 25 Nm
63

Connect the startup battery ground cable.For additional information, please refer to the official Workshop Manual. Battery Disconnect and Connect (414-01)

64

Install the left side loadspace trim panel. For additional information, please refer to the official Workshop Manual. Loadspace Trim Panel LH/RH (501-05)

65

Install the loadspace trim.

66
NOTE
  • This step only applies to vehicles equipped with a spare wheel.

Install the spare wheel.

67
NOTE
  • This step only applies to vehicles not equipped with a spare wheel.

68

Install the loadspace floor trim in the illustrated sequence.

69

Raise the vehicle.

70

Secure the wiring harness retaining clip.

71

Install the side undershields.

72

Install the centre undershield.

73

Install the engine undershield.

  • Torque: 7 Nm
74
NOTE
  • Left side shown. Right side is similar.

Identify the location of the fixing hole for the deployable side step motor cover in the front wheel arch liner. Drill one hole using a 5 mm drill.

75
NOTE
  • Left side shown. Right side is similar.

Secure the deployable side step motor cover to the wheel arch liner.

76
CAUTION
  • Only tighten the bolts finger tight at this stage.
NOTE
  • Left side shown. Right side is similar.

Secure the deployable side step (A) to the mounting brackets using bolts (P).

77
NOTE
  • Left side shown. Right side is similar.

Make sure the deployable side step is correctly positioned in relation to the front bracket as illustrated.

78
NOTE
  • Left side shown. Right side is similar.

Torque the 4 fixing bolts as illustrated.

  • Torque: 12 Nm.
79

Using Land Rover approved diagnostic equipment, configure the deployable side step electrics.

© Land Rover 2016